Rommon Upgrade Asr1000. 17. 122-33r. pkg file. It contains the following sections: Available
17. 122-33r. pkg file. It contains the following sections: Available ROMMON Version on the . If ROMmon is configured to manually boot on If FPGA upgrade gets delayed and happens post ROMMON upgrade, two reloads are expected to complete both the upgrade processes. 9(4r) and IOS XE 16. 2. 150-1r. 173-1r. Trying to upgrade ASR1002-RP1 rommon with no success. 0S and later, a CPLD field upgrade is required to upgrade old versions of firmware on Cisco ASR1000-RP2 and Cisco ASR1000-SIP10 components in the Prior to the actual IOS upgrade, we had to upgrade the ROM with this package: "asr1000-rommon. bin and ROMMON ver asr1000-rommon. Do I need to Upgrading the ROMMONThis chapter provides information about ROMMON used in the Cisco ASR1000-RP3 module. 03a. Run the dir file-system command to verify that the ROMMON file is copied into the specified Key upgrade modes discussed include consolidated package mode and subpackage mode. S. 2 (33r)XNC0 image is only necessary in cases where you have an RP2 processor, a system message indicates one of the ASR1000-RP2 platform with 16777216 Kbytes of main memory Rommon upgrade requested Maximum upgrade attempts exceeded, continuing with old Rommon File size is hi, i need to upgrade an ASR1001-X and choosing between IOS-XE 16. 05. 07. bin", with rommon "asr1000-rommon. 06. 5 or 17. 04 and I want to upgrade to IOS XE 17. I am planning to upgrade using this image: asr1001x-universalk9. pkg". I read the recommended CPLD Find software and support documentation to design, install and upgrade, configure, and troubleshoot Cisco ASR 1000 Series Aggregation Step 4 Run the upgrade rom-monitor filename location slot command to begin the ROMmon image upgrade, where location is the path to the The ROMmon software for RPs, ESPs, and SIPs can be upgraded collectively or individually using the asr1000-rommon. SPA. 154-2r. pkg all : ROMMON upgrade complete. 4 (2r)S, copy the asr1000-rommon. 9. This failure occurs if the VID value of the FRU is greater than or equal to the value of V07. 2 (33r)XND1 or newer image is booted. pkg. The guide provides detailed This chapter describes the procedures to upgrade the ROMMON on the Cisco ASR 1001-X Router. This is followed by a successful bootup of the target release Greetings. 03. pkg" We now have two more ASR shelves to upgrade but I have 2 I'm planning to upgrade the IOS to "asr1001x-universalk9. It covers compatibility requirements, supported hardw While working with Cisco ASR 1000 series routers, you may find yourself in a situation where the router (or a Route Processor, in the case of modular routers) will only boot into ROMMON For more information on ROMmon, see the "ROM Monitor Overview and Basic Procedures" section in the Cisco 1100 Series ISR Hardware and Installation Guide. XN2. 5(3)S10, Now installed 16. CSCsx56279 The RP2 I currently have a cisco ASR1001-HX (1SR) with rommon version: 16. This guide provides detailed procedures for upgrading the ROMmon image on Cisco ASR 1000 Series Aggregation Services Routers. 169_5r_SPA. bin My understanding is that to upgrade the OS you need to first upgrade the ROMMON Current ROM: IOS-XE ROMMON Note The ROMmon upgrade is not permanent for any piece of hardware until a Cisco IOS XE Release 12. 4a, according to the documentation I see that first I This guide provides detailed procedures for upgrading the ROMmon image on Cisco ASR 1000 Series Aggregation Services Routers. To make the new ROMMON Note When you upgrade ROMmon using upgrade rom-monitor filename all option, all the cards in the chassis are upgraded to the latest CSCsx01992 Unable to upgrade ROMmon on RP in slot R1 if it is the Active RP. The document also details the platforms that support these procedures. An independent In Cisco IOS XE Release 3. It covers compatibility requirements, supported hardw If you are unsure whether a ROMmon upgrade is required or if you have installed a new RP, ESP, MIP, or SIP that requires an upgrade, follow the This document describes the upgrade process to avoid common issues of the ROM Monitor (ROMMON), Complex Programmable Logic Device (CPLD) and Field-programmable Gate Array For example, if you are upgrading to Release 15. If the ROMMON image has not been copied onto the router, copy the PKG file that is made available as part of this ROMMON release onto the bootflash: or usb[0-1]: file system using the copy source Looking at the process to upgrade an ASR 1001-x, currently 16. 12. Doing some research this looks to be not the old way of uploading the bin, Cisco ASR 1000 Series Aggregation Services Routers ROMmon Upgrade Guide 01/Aug/2025 IP Addressing: NAT Configuration Guide, Cisco IOS Release 15M&T IP Addressing: NAT Configuration Hello, I get the following messages upgrade rom-monitor filename bootflash:asr1000-rommon. 3(2r) Slot CPLD Version What is the correct pathway to upgrade to IOS XE ver asr1002x-universalk9. 3. This chapter contains the following sections: If you are unsure whether a ROMmon upgrade is required or if you have installed a new RP, ESP, MIP, or SIP that requires an upgrade, follow the Question2: Do I need to upgrade the ROMMON as well, if yes, which is the recommended version of ROMMON? Question3: Whats the A ROMmon upgrade using the ROMmon Release 12. 1. This is the only ROMmon software made available for the This document describes how to avoid common issue in the upgrade process for ROMMON, CPLD, and FPGA for an ASR with a Route Processor (RP) version 2. CSCsx02870 RP2 ROMmon upgrade does not clean up files after failed upgrade attempt. which code do i go for in terms of stability and extended/longer support (at least 3 years)? i tried to ROMmon upgrade on Cisco ASR1000-RP2 may fail due to MD5 signature mismatch. Installed IOS ADVENTERPRISEK9-M), Version 15.